GE Fanuc Automation

pdf
Số trang GE Fanuc Automation 330 Cỡ tệp GE Fanuc Automation 854 KB Lượt tải GE Fanuc Automation 0 Lượt đọc GE Fanuc Automation 36
Đánh giá GE Fanuc Automation
4.2 ( 15 lượt)
Nhấn vào bên dưới để tải tài liệu
Đang xem trước 10 trên tổng 330 trang, để tải xuống xem đầy đủ hãy nhấn vào bên trên
Chủ đề liên quan
Card Power operator power power operator architecture built curriculum electricity circuit Parameters input output

Nội dung

GE Fanuc Automation Computer Numerical Control Products Series 16 / 18 / 160 / 180 – Model C Parameter Manual GFZ-62760EN/01 December 1995 GFL-001 Warnings, Cautions, and Notes as Used in this Publication Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply. ©Copyright 1995 GE Fanuc Automation North America, Inc. All Rights Reserved. PREFACE B–62760EN/01  The mode covered by this manual, and their abbreviations are : Product Name Abbreviations FANUC Series 16–TC 16–TC FANUC Series 160–TC 160–TC FANUC Series 16–MC 16–MC FANUC Series 160–MC 160–MC FANUC Series 18–TC 18–TC FANUC Series 180–TC 180–TC FANUC Series 18–MC 18–MC FANUC Series 180–MC 180–MC T series or T series (two–path control) *1 M series or M series (two–path control) *1 T series or T series (two–path control) *1 M series Note Some functions described in this manual may not be applied to some products. For details, refer to the DESCRIPTIONS (B–62752JA). The table below lists manuals related to MODEL C of Series 16, Series 18, Series 160, Series 180. In the table, this manual is maked with an asterisk (*). Table 1 Related manuals Manual name Specification Number DESCRIPTIONS B–62752EN CONNECTION MANUAL (Hardware) B–62753EN CONNECTION MANUAL (Function) B–62753EN–1 OPERATOR’S MANUAL FOR LATHE B–62754EN OPERATOR’S MANUAL FOR MACHINE CENTER B–62764EN MAINTENANCE MANUAL B–62755EN PARAMETER MANUAL B–62760EN PROGRAMMING MANUAL (Macro Compiler/Macro Executer) B–61803E–1 FAPT MACRO COMPILER PROGRAMMING MANUAL B–66102E FANUC Super CAP T OPERATOR’S MANUAL B–62444E–1 FANUC Super CAP M OPERATOR’S MANUAL B–62154E * PREFACE B–62760EN/01 Table 1 Related manuals Manual name Specification Number FANUC Super CAP M PROGRAMMING MANUAL B–62153E CONVERSATIONAL AUTOMATIC PROGRAMMING FUNCTION I FOR LATHE OPERATOR’S MANUAL B–61804E–1 CONVERSATIONAL AUTOMATIC PROGRAMMING FUNCTION FOR LATHE OPERATOR’S MANUAL B–61804E–2 B–62760EN/01 Table of contents 1. DISPLAYING PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. SETTING PARAMETERS FROM MDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. INPUTTING AND OUTPUTTING PARAMETERS THROUGH THE READER/PUNCHER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 OUTPUTTING PARAMETERS THROUGH THE READER/PUNCHER INTERFACE . . . . . . . . . 6 3.2 INPUTTING PARAMETERS THROUGH THE READER/PUNCHER INTERFACE . . . . . . . . . . . 7 4. DESCRIPTION OF PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.1 PARAMETERS OF SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2 PARAMETERS OF READER/PUNCHER INTERFACE, REMOTEBUFFER, DNC1, DNC2, AND M–NET INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.3 PARAMETERS OF AXIS CONTROL/ INCREMENT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 4.4 PARAMETERS OF COORDLNATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 4.5 PARAMETERS OF STROKE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 4.6 PARAMETERS OF THE CHUCK AND TAILSTOCK BARRIER (16–TB) . . . . . . . . . . . . . . . . . . . 56 4.7 PARAMETERS OF FEEDRATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 4.8 PARAMETERS OF ACCELERATION/ DECELERATION CONTROL . . . . . . . . . . . . . . . . . . . . . . 72 4.9 PARAMETERS OF SERVO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 4.10 PARAMETERS OF DI/DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 4.11 PARAMETERS OF CRT/MDI, DISPLAY, AND EDIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 4.12 PARAMETERS OF PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 4.13 PARAMETERS OF PITCH ERROR COMPENSATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 4.14 PARAMETERS OF SPINDLE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 4.15 PARAMETERS OF TOOL COMPENSATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 4.16 PARAMETERS RELATED TO GRINDING–WHEEL WEAR COMPENSATION . . . . . . . . . . . . . 185 4.17 PARAMETERS OF CANNED CYCLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 4.18 PARAMETERS OF RIGID TAPPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 4.19 PARAMETERS OF SCALING/COORDINATE ROTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 4.20 PARAMETERS OF UNI–DIRECTIONAL POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 4.21 PARAMETERS OF POLAR COORDINATE INTERPOLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 4.22 PARAMETERS OF NORMAL DIRECTION CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 4.23 PARAMETERS OF INDEXING INDEX TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 4.24 PARAMETER FOR INVOLUTE INTERPOLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 4.25 EXPONENTIAL INTERPOLATION PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 4.26 STRAIGHTNESS COMPENSATION PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 4.27 PARAMETERS OF CUSTOM MACROS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 4.28 PARAMETERS RELATED TO PATTERN DATA INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 4.29 PARAMETER OF SKIP FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 4.30 PARAMETERS OF AUTOMATIC TOOL COMPENSATION (16–TB) AND AUTOMATIC TOOL LENGTH COMPENSATION (16–MB) . . . . . . . . . . . . . . . . . . . . . . . . . 236 4.31 PARAMETER OF EXTERNAL DATA INPUT/OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 4.32 PARAMETERS OF GRAPHIC DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 4.33 PARAMETERS OF DISPLAYING OPERATION TIME AND NUMBER OF PARTS . . . . . . . . . . . 243 i Table of contents B–62760EN/01 4.34 PARAMETERS OF TOOL LIFE MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 4.35 PARAMETERS OF POSITION SWITCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 4.36 PARAMETERS OF MANUAL OPERATIONAND AUTOMATIC OPERATION . . . . . . . . . . . . . . 252 4.37 PARAMETERS OF MANUAL HANDLE FEED, HANDLE INTERRUPTION AND HANDLE FEED IN TOOL AXIAL DIRECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 4.38 PARAMETERS RELATED TO BUTT–TYPE REFERENCE POSITION SETTING . . . . . . . . . . . . 257 4.39 PARAMETERS OF SOFTWARE OPERATOR’S PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 4.40 PARAMETERS OF PROGRAM RESTART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 4.41 PARAMETERS OF HIGH–SPEED MACHINING (HIGH–SPEED CYCLE MACHINING/HIGH– SPEED REMOTE BUFFER) . . . . . . . . . . . . . . . . . 263 4.42 PARAMETERS OF POLYGON TURNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 4.43 PARAMETERS OF THE EXTERNAL PULSE INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 4.44 PARAMETERS OF THE HOBBING MACHINE AND ELECTRONIC GEAR BOX . . . . . . . . . . . 271 4.45 PARAMETERS OF AXIS CONTROL BY PMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 4.46 PARAMETERS OF TWO–PATH CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 4.47 PARAMETERS FOR CHECKING INTERFERENCE BETWEEN TOOL POSTS (TWO–PATH CONTROL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 4.48 PARAMETERS RELATED TO PATH AXIS REASSIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 4.49 PARAMETERS FOR ANGULAR AXIS CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 4.50 PARAMETERS RELATED TO B–AXIS CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 4.51 PARAMETERS OF SIMPLE SYNCHRONOUS CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 4.52 PARAMETERS OF RELATED TO CHECK TERMINATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 4.53 CHOPPING PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 4.54 PARAMETERS OF HIGH–SPEED HIGH–PRECISION CONTOUR CONTROL BY RISC (16–MB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 4.55 OTHER PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317 4.56 PARAMETERS FOR MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 APPENDIXES A. CHARACTER CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 ii 1. DISPLAYING PARAMETERS B–62760EN/01 1 DISPLAYING PARAMETERS Follow the procedure below to display parameters. (1) Press the SYSTEM function key on the CRT/MDI as many times as required, or alternatively, press the SYSTEM function key once, then the PARAM section select soft key. The parameter screen is then selected. POS PROG OFFSET SETTING SYSTEM MESSAGE GRAPH CUSTOM Function keys Note Pressing the SYSTEM function key displays section select soft keys including PARAM. > MEM STRT MTN FIN *** 10:02:30 [ PARAM ] [ DGNOS ] [ PMC ] [ SYSTEM ] [ (OPRT) ] Return menu key Soft keys ← Soft key display (section select) Continuous menu key (2) The parameter screen consists of multiple pages. Use step (a) or (b) to display the page that contains the parameter you want to display. (a) Use the page select key or the cursor move keys to display the desired page. (b) Enter the data number of the parameter you want to display from the keyboard, then press the [NO.SRH] soft key. The parameter page containing the specified data number appears with the cursor positioned at the data number. (The data is displayed in reverse video.) Note If key entry is started with the section select soft keys displayed, they are replaced automatically by operation select soft keys including [NO.SRH]. Pressing the [(OPRT)] soft key can also cause the operation select keys to be displayed. 1 1. DISPLAYING PARAMETERS B–62760EN/01 Data entered from the keyboard Soft key display ← (section select) ← > MEM STRT MTN FIN *** 10:02:34 [ NO. SRH ] [ ON:1 ] [ OFF:0 ] [ +INPUT ] [ INPUT ] O0001 N00010 PARAMETER (FEEDRATE) 1401 RDR 0 0 1402 1410 1412 1420 0 0 0 JRV 0 0 0 0 0 DRY RUN FEEDRATE RAPID FEEDRATE X Y Z JZR 0 0 0 RPD 0 0 0 10000 0 15000 15000 15000 > MEM STRT MTN FIN *** 10:02:35 [ NO. SRH ] [ ON:1 ] [ OFF:0 ] [ +INPUT ] [ INPUT ] 2 Cursor 2. SETTING PARAMETERS FROM MDI B–62760EN/01 2 SETTING PARAMETERS FROM MDI Follow the procedure below to set parameters. (1) Place the NC in the MDI mode or the emergency stop state. (2) Follow the substeps below to enable writing of parameters. 1. To display the setting screen, press the SETTING function key as many times as required, or alternatively press the SETTING function key once, then the SETTING section select soft key. The first page of the setting screen appears. 2. Position the cursor on “PARAMETER WRITE” using the cursor move keys. SETTING (HANDY) PARAMETER WRITE TV CHECK PUNCH CODE INPUT UNIT I/O CHANNEL O0001 N00010 = = = = = 0 0 0 0 0 (0:DISABLE 1:ENABLE) (0:OFF 1:ON) (0:EIA 1:ISO) (0:MM 1:INCH) (0–3:CHANNEL NO.) 3. Press the [(OPRT)] soft key to display operation select soft keys. > 1410 MDI STOP *** *** *** 10:03:02 [ NO. SRH ] [ ON:1 ] [ OFF:0 ] [ +INPUT ] [ INPUT ] ← Data entered from the keyboard ← Soft key display (section select) 4. To set “PARAMETER WRITE=” to 1, press the ON:1 soft key, or alternatively enter 1 and press the INPUT soft key. From now on, the parameters can be set. At the same time an alarm condition (P/S100 PARAMETER WRITE ENABLE) occurs in the CNC. (3) To display the parameter screen, press the SYSTEM function key as many times as required, or alternatively press the SYSTEM function key once, then the PARAM section select soft key. (See “1. Displaying Parameters.”) (4) Display the page containing the parameter you want to set, and position the cursor on the parameter. (See “1. Displaying Parameters.”) (5) Enter data, then press the [INPUT] soft key. The parameter indicated by the cursor is set to the entered data. 3 L2. SETTING PARAMETERS FROM MDI B–62760EN/01 [Example] 12000 [INPUT] PARAMETER (FEEDRATE) 1401 RDR 0 0 1402 1410 1412 1420 O0001 N00010 0 0 0 JRV 0 0 0 0 0 DRY RUN FEEDRATE RAPID FEEDRATE X Y Z JZR 0 0 0 RPD 0 Cursor 0 0 12000 0 15000 15000 15000 > MDI STOP *** *** ALM 10:03:10 [ NO. SRH ] [ ON:1 ] [ OFF:0 ] [ +INPUT ] [ INPUT ] Data can be entered continuously for parameters, starting at the selected parameter, by separating each data item with a semicolon (;). [Example] Entering 10;20;30;40 and pressing the INPUT key assigns values 10, 20, 30, and 40 to parameters in order starting at the parameter indicatedby the cursor. (6) Repeat steps (4) and (5) as required. (7) If parameter setting is complete, set “PARAMETER WRITE=” to 0 on the setting screen to disable further parameter setting. (8) Reset the NC to release the alarm condition (P/S100). If an alarm condition (P/S000 PLEASE TURN OFF POWER) occurs in the NC, turn it off before continuing operation. Note The bits left blank in 4. DESCRIPTION OF PARAMETERS and the parameter numbers that appear on the CRT screen but are not found in the parameter list are reserved for future expansion. They must always be 0. 4
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.